
ServicesWindow Replacement
Window Replacement in Buena Park
We take out old windows that stick, leak air or fog up, and put in new ones that open easy and seal tight. We measure every opening ourselves, show you your options at the kitchen table and clean up before we leave.
New windows, put in the way we'd want them in our own place
Plenty of houses in this area are still running on the aluminum sliders they were built with. One pane of glass, skinny frames, tracks worn down from decades of use. They let the summer heat pour in and shake when the wind picks up. Swapping them out is often the single biggest change you can make to how a room feels.
We treat your home like a neighbor's. That means straight answers about what you need, no pushing the top-of-the-line unit when a mid-range window does the job, and a crew that covers your floors and hauls the old glass away.
Most jobs use a retrofit install, where the new window fits inside the existing frame so your stucco stays untouched. If the old frame is too far gone, we'll tell you and explain what a full-frame install involves. Our Window Retrofitting page goes into that in more detail.
Your window job, start to finish
Our own measurements
No guessing from a catalog. We check the width and height of each opening at three points, because older houses settle and few openings are truly square. Sizing to those numbers keeps gaps small and seals tight.
Help picking the window
We walk you through frame materials, glass packages and styles like sliders, single-hung and picture windows. You get a plain answer about which ones make sense for each room.
Careful removal
Old sashes and panels come out without cracking the stucco or scratching the trim. Broken glass goes straight into our bins, not your yard.
Install and seal
Each window is set level and plumb, shimmed and fastened. We seal the outside against water and air, then trim and caulk so it looks finished from both sides.
Cleanup and haul-away
We vacuum the sills, wipe down the new glass and take every old frame with us. You won't be left with a pile by the trash cans.

How to tell your windows are due
- Haze inside the glass
- A cloudy dual-pane window has a broken seal. The insulating gas has escaped, and the haze will not go away.
- Sliders that are hard to move
- Worn rollers and bent tracks make windows tough to open and tougher to lock. That is a safety concern, not only a nuisance.
- A room that runs hot
- When one room is always warmer than the others, single-pane glass facing the afternoon sun is often why. New low-E glass cuts much of that heat.
- Air leaks and gritty sills
- Gaps around worn frames let in air, dust and street noise. Wipe the sill and you'll find grit on it again the next day.
- Wet frames on cool mornings
- Aluminum frames turn cold and drip on winter mornings. That moisture stains sills over time and can lead to mildew.
Step by step
- 1
Free estimate at your home
We visit, check each window, measure and hear what you want. Your quote comes by phone or in person, broken out line by line, with no pressure and no obligation.
- 2
Placing the order
When you give the go-ahead, we order windows made to the sizes we measured. You get an install date once they come in.
- 3
The install
We start by laying drop cloths. Then we go one opening at a time, pulling an old unit and setting the new one before moving on, so no part of the house stays open longer than needed.
- 4
Walking it with you
Before we pack up, you test every new window: slide it, close it, lock it. Anything that drags or won't latch cleanly gets adjusted right then, before we leave.
What sets the price
Every house is different, so we price after we've seen it. Your quote lists each window and what goes into it, so you can see where the money goes. If you have questions about any line, ask, and we'll walk you through it.
- Number and size of windows
- More windows usually lower the cost per opening. Very large panes or odd shapes take more glass and more labor.
- Frame and glass choices
- Vinyl, fiberglass and specialty frames vary. Low-E coatings, tempered glass and obscure glass for bathrooms each add to the cost.
- Retrofit or full-frame
- A retrofit install that leaves the old frame in place is quicker. Tearing out the whole frame means stucco and trim work, which adds time.
- Access
- Second-story windows, tight side yards and windows behind heavy landscaping take more setup. We factor that in up front.
Common window replacement questions
- Is there a special on window replacement?
- There is. Window replacement for only $495 per window with free installation (minimum purchase of 4 windows per order; some glass size and product restrictions apply). At the estimate we point out which of your windows qualify.
- Do you have to cut into the stucco?
- In most cases, no. A retrofit sets the new window inside the existing frame and leaves the stucco as it is. When the old frame is damaged, full-frame may be the smarter choice, and we explain why before you agree to anything.
- How long from start to finish?
- Each window is built to a custom size, so there is a wait after you approve the order. Once they're here, most homes take one day. Larger homes and full-frame work can take more, and we give you a realistic timeline at the estimate.
- Do I need to stay home the whole day?
- No. An adult just needs to let the crew in when we arrive and look over the work with us when we finish. Do what you like in between. We work one room at a time, so the rest of the house stays usable.
- Can my sliding glass door be done at the same time?
- It can. Many homeowners pair the two, since an old door usually matches the old windows. Our Sliding Door Replacement page explains how that job goes.

Have us check your windows
We'll stop by, take measurements and tell you honestly what needs replacing now and what can wait. You get a clear quote and no sales pitch.